AiPTS0101

AiPLS0102 is a voltage level translator. The circuit supports bidirectional multi-voltage level translationin the range of 0.8V to 5V without direction control.

AiP2206 is a bidirectional IC-bus and SMBus voltage-level translator with an enableport and isoperational from 1.0V to 3.6V(Vreft1))and 1.8V to 5.5V(Vbis(ref2)).AiP2206 allows bidirectional voltage-level translation from IV to 5V without the use of direction pins.The low ON-state resistance of the switch allows connections to be made with minimal propagation delayWhen the enable port is high, the translator switch is on, and SCLI and SDAl are connected to SCL.2 andSDA2 respectively, allowing data transmission at both ends. When the enable port is low, the switch is offand the ports are high-impedance state. AiP2206 will isolate both sides when the device is disabled, and provides voltage-level translation whenenabled.AiP2206 can be used to run two buses, one is at 400kHz operating frequency and the other is at 100kHzoperating frequency. If these two buses are at different frequencies, the 100kHz bus must be isolated whenthe other bus is operating at 400kHz. If the controller runs at 400kHz, the maximum system operatingfrequency may be lower than 400kHz due to the delay of the translation.Like the standard 12C system, AiP2206 needs to provide logic high level for translation bus throughpull-up resistor. AiP2206 has a standard 12C bus open-collector configuration. The pull-up resistance isdetermined by the transmission rate of the system, but both ends of the translator must have pull-upresistors. This device mainly works in IC bus devices of standard mode, fast mode and fast mode Plus tocooperate with SMBus devices. The maximum frequency depends on the RC time constant, but it isgenerally allowed more than 2MHz When the SDAl or SDA2 port is low level, it is ON-state betweenSDAl and SDA2 and there is a small ON-state resistor. Assuming that the reference high level of thedevice at SDA2 is higher than the reference high level of the device at SDA1, the output voltage at SDA1will be limited to the voltage set by VREFI when the device at SDA2 outputs a high level. When thedevice at SDAl outputs a high level, SDA2 is pulled up by pul-up resistor to the high level set by thedrain pull-up power supply voltage (VpuD). This allows users to freely switch high and low levels withoutdirection control pins. The operating principle of SCL 1/SCL2 channel is the same as that of SDAl/SDA2channel. All the channels have the same electrical characteristics, and there is a slight deviation in voltage orpropagation delay from one side to the other. Symmetric manufacturing of switches is beneficial to solvethe voltage-level translation of split transistors. The translator provides excellent ESD protection for low-voltage devices, and at the same time, it protects devices lacking electrostatic protection.

AiPGTL2003 is a voltage level translator. The circuit supports bidirectional multi-voltage level translation in the range of 0.8V to 5V without direction control.

The AiPGTL2014 is a 4-bit GTL-LVTTL bidirectional transceiver. LVTTL is the typical COMS input/output; GTL parameters allow free configuration: the level input threshold is provided externally, the output is open leakage output, and the high level is provided by external pull-up resistor, which can meet a variety of GTL level requirements.

The AiPTS0101 is a 1-bit, dual supply translating transceiver with auto direction sensing, that enables bidirectional voltage level translation. It features two 1-bit input-output ports (A and B), one output enable input (OE) and two supply pins (VCC(A) and VCC(B)). 

The AiPTS0102 is a 2-bit, dual supply translating transceiver with auto direction sensing, that enables bidirectional voltage level translation. It features two 1-bit input-output ports (A and B), one output enable input (OE) and two supply pins (VCC(A) and VCC(B)). 

The AiPTS0103 is a 3-bit, dual supply translating transceiver with auto direction sensing, that enables bidirectional voltage level translation. It features two 1-bit input-output ports (A and B), one output enable input (OE) and two supply pins (VCC(A) and VCC(B)). 

The AiPTS0104 is a 4-bit, dual supply translating transceiver with auto direction sensing, that enables bidirectional voltage level translation. It features two 1-bit input-output ports (A and B), one output enable input (OE) and two supply pins (VCC(A) and VCC(B)). 

The AiPTS0108is a 8-bit, dual supply translating transceiver with auto direction sensing, that enables bidirectional voltage level translation. It features two 1-bit input-output ports (A and B), one output enable input (OE) and two supply pins (VCC(A) and VCC(B)). 

The AiPTB0101 is an 8-bit, dual supply translating transceiver with auto direction sensing, that enables bidirectional voltage level translation. It features two 8-bit input-output ports (An and Bn), one outputenable input (OE) and two supply pins (VCC(A) and VCC(B)). 

The AiPTB0102 is an 8-bit, dual supply translating transceiver with auto direction sensing, that enables bidirectional voltage level translation. It features two 8-bit input-output ports (An and Bn), one outputenable input (OE) and two supply pins (VCC(A) and VCC(B)). 

The AiPTB0104 is an 8-bit, dual supply translating transceiver with auto direction sensing, that enables bidirectional voltage level translation. It features two 8-bit input-output ports (An and Bn), one outputenable input (OE) and two supply pins (VCC(A) and VCC(B)). 

The AiPTB0106 is an 8-bit, dual supply translating transceiver with auto direction sensing, that enables bidirectional voltage level translation. It features two 8-bit input-output ports (An and Bn), one outputenable input (OE) and two supply pins (VCC(A) and VCC(B)). 

The AiPTB0108 is an 8-bit, dual supply translating transceiver with auto direction sensing, that enables bidirectional voltage level translation. It features two 8-bit input-output ports (An and Bn), one outputenable input (OE) and two supply pins (VCC(A) and VCC(B)). 

The AiP74HC/HCT4067 is a single-pole 16-throw analog switch (SP16T) suitable for use in analog or digital 16:1 multiplexer/demultiplexer applications. The switch features four digital select inputs (S0, S1,S2 and S3), sixteen independent inputs/outputs (Yn), a common input/output (Z) and a digital enable input(E—).